Bmb-home HOME PROTECTOR+ Manuale Utente Pagina 21
- Pagina / 32
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
P/N 033000=13610 Rev. 01-02-06 BMB Home Security
21
7.9 Clearing the timer settings
1. To access the menu, press the menu UP or menu DOWN ?button. The display now shows ENTER PIN.
2. Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). The display is cleared
and shows a * for each number entered.
3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.
4. Use the menu buttons UP/DOWN? ?to go to menu item 9. SET TIMER. Press OK to select this menu item. You can
also go to this menu item directly by pressing a 9 on the number pad.
5. The display will read NEW TIMER.
6. Use the menu buttons UP/DOWN? ?to check timers you set before. The timers are shown in the following
format: 12 ON 12:40
OFF 18:30
7. When a timer is shown, you can press CLEAR to delete the timer.
8. You need to confirm your choice (CLEAR TIMER). Press 1 for Yes and 2 for No.
9. Press CLEAR again to quit the menu.
8. Advanced system functions
8.1 Setting the delays
You can set a number of delay times via the menu DELAYS:
ENTRY DELAY The time you get to switch off the system after entering your house (factory setting 30 sec).
EXIT DELAY before the system is switched on when you leave the house (factory setting 60 sec).
ANSWER DELAY before the system picks up the line when calling in (11.2, factory setting 5 sec).
DIAL DELAY before the system calls out in case of an alarm (factory setting 30 sec).
Setting the delays:
1. To access the menu, press either the menu UP ?or DOWN ?button. The display now shows ENTER PIN.
2. Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). The display is cleared
and shows a * for each number entered.
3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.
4. Use the menu buttons UP/DOWN? ?? to go to menu item 8. DELAYS. Press OK to select this menu item. You can
also go to this menu item directly by pressing an 8 on the number pad.
5. Select ENTRY DELAY, EXIT DELAY, ANSWER DELAY or DIAL DELAY and press OK.
6. Enter the time required (1-99 seconds). Press OK. Press CLEAR to delete the values entered.
7. Press CLEAR again to quit the menu.
The entry delay only works for the DS18 Door/Window Sensors if set to MAX as well as Motion Sensors
registered to zone 15 and/or 16. MS18 motion detectors registered to other zones will respond instantly.
8.2 Clearing the memory of your security system
You can delete sensors, remote controls, timers or all settings via the menu MEMORY CLEAR.
The PIN code is never erased. This code can only be reset by the factory.
1. To access the menu, press the menu UP? or menu DOWN ?button. The display now shows ENTER PIN.
2. Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). The display is cleared
and shows a * for each number entered.
3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.
4. Use the menu buttons UP/DOWN? ?? to go to menu item 6. MEMORY CLEAR. Press OK to select this menu item. You
can also go to this menu item directly by pressing a 6 on the number pad.
5. Select CLEAR ALL SENSORS, CLEAR ALL REMOTES, CLEAR ALL TIMERS, CLEAR ALL THERMOSTATS, CLEAR LOG or MASTER RESET.
6. You are now asked to CONFIRM CLR. Press 1 for Yes or 2 for No.
7. Press CLEAR again to quit the menu.
CLEAR ALL SENSORS Remove a registered sensor.
CLEAR ALL REMOTES Remove a registered remote control or Additional (wireless) sensor.
CLEAR ALL TIMERS Remove all timer settings at once.
CLEAR ALL THERMOSTATS Remove all thermostats at once.
CLEAR LOG Remove Event Log.
MASTER RESET Clear the memory completely (PIN will remain as set).
8.3 Changing the access code (PIN)
The access code is your personal identification code. After changing this code, you are the only one who has
access to the settings on the console. You also use this code to disarm the alarm via the number pad. Make
sure you memorise the code, because only the factory, or authorized representative can help you reset the code
to the factory setting (0000).
Prodotti e manuali riguardandi Sistemi di controllo di accesso Bmb-home HOME PROTECTOR+
(6 pagine)
(8 pagine)Candy GO4 107DF__L-01 manuali
Manuali dei proprietari e guide per l'utente per Lavatrici Candy GO4 107DF__L-01.
We fornisce 1 manuali pdf Candy GO4 107DF__L-01 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commenti su questo manuale